WHITE LED NAME CARD



White LED Name Card, retail $19.95
Manufactured by (Unknown)
Last updated 02-02-11





Thuh kompenie thaat maks thuh LED Name Card kant spel...O WAIT!!! They spelled all of the words in the name of this product "kerrektlee".
The White LED Name Card was purchased on Ebay, while I was looking for another product.

The White LED Name Card is remarkably easy to use; just pop two of the four included batteries in it, and program it via the three buttons on its back. It is comparable in ease to entering your initials after reaching a high score on a coin-op arcade video game like they had in the 1980s and 1990s - and probably the early-2000s too; though I have not played one of the coin-op arcade video games from this decade so I cannot confirm how high score monitoring is performed on modern equipment.

Yes, it really is that easy.

It scrolls your message in white LED lights on its front surface; you can have up to six messages (512 characters & spaces for the first message, 256 characters & spaces for messages 2 through 6).

The name on the front of the package is "DIGIGR8 LED NAME CARD".


 SIZE



To use the White LED Name Card, first install two of the four included the batteries into it (see below), and then you'll be ready to rock.

On the back of the unit, there are three slim pushbutton switches: "ENTER/ON/OFF", "PAGE UP" (P-U), and "PAGE DOWN" (P-D). These switches have a noticeable clicking sound and a firm tactile sensation (a "click" sensation you can feel) when they are actuated, so there is no mistake when the switches are pressed.

Press the "ENTER/ON/OFF" button to turn the product on; press it again to turn the product off.

When the badge is on (displaying a message), pressing the P-U or P-D buttons selects switch display info (message you want to display; 1-6 - "SWITCH"), input text mode ("INPUT"), display scrolling speed ("SPEED"), or LED brightness control ("LUM").

The first option you'll want to select is "SWITCH" mode to select which block of memory you want to use to store a message. When "SWITCH" is scrolling on the unit's display, press the "ENTER/ON/OFF" button, and then the "P-U" or "P-D" buttons to select page 1, 2, 3, 4, 5, or 6. Press the "ENTER/ON/OFF" button to lock in your choise.

When the badge is on (displaying a message), press the "P-U" or "P-D" buttons to select input text mode ("INPUT"); press the "ENTER/ON/OFF" button, and you'll be in text entry mode.

Change the letter on the right side of the display using the "P-U" and "P-D" buttons; use the "ENTER/ON/OFF" button to lock that character into the unit's memory and move to the next. When you need to add a space (such as between words so it "doesn'tlooklikethis"), it is found right past the uppercase "Z". If you make a mistake and need to delete a character, press & hold the "ENTER/ON/OFF" button for three seconds. When you are finished entering your message, either press and hold the "P-D" button for three seconds or wait (do not press any buttons) for ~10 seconds. The message you entered will then automatically scroll from right to left on the unit's LED display.

Uppercase and lowercase letters, the characters above the number keys (!, @, #, $, %, ^, &, *, (, and )), the numerals 0-9, and various punctuation characters are all available.


In this example, I am inputting the phrase "{vulgar term for urine} OFF, {vulgar term for urine} ANT!" into the product.

To select scrolling speed, turn the unit on, press the "P-U" or "P-D" buttons until "SPEED" is scrolling on the unit's display, press the "ENTER/ON/OFF" button, and then the "P-U" or "P-D" buttons to select speeds 1, 2, 3, 4, 5, 6, 7, 8, or 9. Press the "ENTER/ON/OFF" button to lock in your choise.
1 is the slowest, 9 is the fastest.

To select brightness, turn the unit on, press the "P-U" or "P-D" buttons until "LUM" is scrolling on the unit's display, press the "ENTER/ON/OFF" button, and then the "P-U" or "P-D" buttons to select brightnesses 1, 2, 3, 4, 5, 6, 7, 8, or 9. Press the "ENTER/ON/OFF" button to lock in your choise.
1 is the dimmest, and 9 is the brightest.

Use the included magnet or the included safety pin to affix the White LED Name Card to a shirt, apron, jacket, or other fabric as you wish.



To remove the batteries, turn the unit upside-down so the back surface faces up. Turn the unit so the door that reads "OPEN" is on the lower left. Use an instrument like a knife blade to slide the door out. When it does come out, remove and dispose of or recycle the used-up old CR2016 cells.

Insert two new CR2016 cells into the opening of this door, orienting them so their flat sides (+) positives faces upward.

With the unit still oriented so the LEDs face down, insert (if necessary) and push in on the door until it is flush with the rest of the unit.



This is a digital scrolling badge, not a flashlight. So I won't throw it against the wall, stomp on it, try to drown it in the {vulgar term for feces}bowl or the cistern, run over it, swing it against the concrete floor of a patio, bash it open to check it for candiosity, fire it from the cannoņata (I guess I've been watching the TV program "Viva Piņata" too much again - candiosity is usually checked with a laser-type device on a platform with a large readout or with a handheld wand), send it to the Daystrom Institute for additional analysis, or inflict upon it punishments that I might inflict upon a flashlight. So this section of its web page will be rather bare, when compared to this section of the web page on a page about a flashlight.

The White LED Name Card has 21 columns of 7 bright white LEDs, for 147 LEDs total.

One of the first things I do when I test a programmable message thing is to see if there's an onboard censor, and there isn't. I input "{vulgar term for a man or woman who acts as a penis vaccume}! {vulgar term for male urinator/inseminator - rhymes with stick} {vulgar slang term for homosexual male - rhymes with the last name of AFV host Bob Sagget; or an archaic term that used to describe a bundle of sticks}" into the White LED Name Card, and it happily spouted off the stream of obcenities.
I soon changed it back to "THANK YOU FOR VISITING WWW.LEDMUSEUM.ORG!!!" just so I wouldn't forget.

So if you have garbage mouth, potty mouth, toilet tongue, sewer mouth, sewer chute, etc. you can input dirty language into the White LED Name Card and have it spew forth with the obcenities when the product is subsequently used.


Photograph of the White LED Name Card affixed to a shirt, as it might normally be used.

Because this device has a fairly strong magnet, you should excersize exteme caution when you use the badge near a heart pacemaker if you have a pacemaker implanted in your chest.

I found the unit remarkably easy to use, considering there is no computer interface or software - all of the product's functions are controlled via three buttons on the back.

This evaluation resemble the ones I made for the Blue LED Badge, the Green LED Badge, and the Red LED Badge?
Thought so. It's because I used them as templates for this one.



I tried to take a photograph of the White LED Name Card while a message was scrolling, but the scrolling speed was fast enough and the camera's shutter speed was slow enough that the photograph did not come out well at all.


Spectrographic analysis
Spectrographic analysis of the LEDs in this badge.


Spectrographic analysis
Same as above; newer spectrometer software & settings used.

USB2000 spectrometer graciously donated by P.L.

WMP movie (.avi extension) showing the White LED Name Card in action.
It shows "THANK YOU FOR VISITING WWW.LEDMUSEUM.ORG" in uppercase (capital) letters scrolling from right to left.
This clip is ~4.2 megabytes (4,309,090 bytes) in length; dial-up users please be aware.
It will take no less than fifteen minutes to load at 48.0Kbps.
I cannot provide it in other formats, so please do not ask.

That sound you ***MIGHT*** hear is a TV commercial playing on the boob tube.
You may also hear some rustling noises; this is from the camera's microphone rubbing up against something.
This product is not sound-sensitive; the sound may be ignored or muted if desired.


WMP movie (.avi extension) showing all four LED name tags I have doing their thing.
The red one displays "HAPPY VALENTINE'S DAY!",
the green & blue ones display "HAPPY BIRTHDAY ANGIE!!!",
and the white one displays "THANK YOU FOR VISITING WWW.LEDMUSEUM.ORG".

This clip is ~4.1 megabytes (4,226,362 bytes) in length; dial-up users please be aware.
It will take no less than fifteen minutes to load at 48.0Kbps.
I cannot provide it in other formats, so please do not ask.

That sound you ***MIGHT*** hear is the program "Viva Piņata" playing on the boob tube.
These products are not sound-sensitive; the sound may be ignored or muted if desired.
From top to bottom: red, green, blue, white.



TEST NOTES:
Sample of the White LED Name Card was purchased on Ebay on 08-21-07 and was received at 2:41pm PDT on 08-24-07.

Unit was purchased at this link, which will go bad after ~11-21-07.

Product was made in China.
A product's country of origin really does matter to some people, which is why I published it on this web page.


UPDATE: 09-09-07
I programmed it to read "TIME FOR YOUR MEDS, ANGIE!!! :-)" a couple of weeks ago, and put it on every morning & evening when I bring my sister her medication.


PROS:



CONS:



    MANUFACTURER: Unknown
    PRODUCT TYPE: Magnetic scrolling LED badge
    LAMP TYPE: Small "chip-type" white LED
    No. OF LAMPS: 147
    BEAM TYPE: N/A
    SWITCH TYPE: Small rubber pushbutton on/off, character up, character down
    CASE MATERIAL: Plastic
    BEZEL: Plastic
    BATTERY: 2xCR2016 lithium coin cells
    CURRENT CONSUMPTION: Unknown/unable to measure
    WATER- AND PEE-RESISTANT: Light sprinkle-resistance at maximum
    SUBMERSIBLE: NO WAY HOZAY!!!
    ACCESSORIES: 4xCR2016 cells, thin bar magnet, safety pin
    SIZE: 3.15"L x 1.60"W x 0.260"D
    WEIGHT: ~1.10oz.
    WARRANTY: Unknown/not stated

    PRODUCT RATING:

    Star Rating





White LED Name Card *







Do you manufacture or sell an LED flashlight, task light, utility light, or module of some kind? Want to see it tested by a real person, under real working conditions? Do you then want to see how your light did? If you have a sample available for this type of real-world, real-time testing, please contact me at ledmuseum@gmail.com.

Please visit this web page for contact information.

Unsolicited flashlights, LEDs, and other products appearing in the mail are welcome, and it will automatically be assumed that you sent it in order to have it tested and evaluated for this site.
Be sure to include contact info or your company website's URL so visitors here will know where to purchase your product.



WHITE 5500-6500K InGaN+phosphor 
ULTRAVIOLET 370-390nm GaN 
BLUE 430nm GaN+SiC
BLUE 450 and 473nm InGaN
BLUE Silicon Carbide
TURQUOISE 495-505nm InGaN
GREEN 525nm InGaN 
YELLOW-GREEN 555-575mn GaAsP & related
YELLOW 585-595nm
AMBER 595-605nm
ORANGE 605-620nm
ORANGISH-RED 620-635nm
RED 640-700nm
INFRARED 700-1300nm
True RGB Full Color LED
Spider (Pirrahna) LEDs
SMD LEDs
True violet (400-418nm) LEDs
Agilent Barracuda & Prometheus LEDs
Oddball & Miscellaneous LEDs
Programmable RGB LED modules / fixtures
Where to buy these LEDs 
Links to other LED-related websites
The World's First Virtual LED Museum
Legal horse puckey, etc.
RETURN TO OPENING/MAIN PAGE
LEDSaurus (on-site LED Mini Mart)



This page is a frame from a website.
If you arrived on this page through an outside link,you can get the "full meal deal" by clicking here.